3D print files

[cyborg]

Flared mouth
Can be sized to fit most any tube
I made one for a large acrylic candy jar
Candy Jar ABS.jpgCandy Jar 2.jpgCandy Jar ABS.zipMVIMG_20200508_180700 2.jpg
Sketchup flare.jpg

You could make a negative of this print and use silicone putty to make the seal. Silicone putty is harder than the liquid silicone.

[Brazilien]

A two-part project like the Monster Tube would be much easier to design and print.

[Pumpernorth1987]

Is there a software that makes it easy to design things?

I installed Blender and freecat but I can't seem to get to grips with them.

I don't even know how to use finished files can edit (change size, etc.).

A simple software where you drag a corner of the model with the mouse to change the model.... So simple

[lennypumper]

Hi Guys,
this is my selfdesigned and printed Tube. It was inspired by my bullmaster jr.
It‘s not as clean as the original, but i have a pretty good Look on the things going on in there…
Many Greets vom Germany…

[Pumpernorth1987]

Hi Guys,
this is my selfdesigned and printed Tube. It was inspired by my bullmaster jr.
It‘s not as clean as the original, but i have a pretty good Look on the things going on in there…
Many Greets vom Germany…

Your print looks really good. What are your settings (wall thickness, layer thickness, etc.) and what material did you use? Greetings from northern Germany

[nohapony]

A two-part project like the Monster Tube would be much easier to design and print.

I have a little something for you: https://www.printables.com/model/796164 ... sball-pump

[lennypumper]

Hi Guys,
this is my selfdesigned and printed Tube. It was inspired by my bullmaster jr.
It‘s not as clean as the original, but i have a pretty good Look on the things going on in there…
Many Greets vom Germany…

Your print looks really good. What are your settings (wall thickness, layer thickness, etc.) and what material did you use? Greetings from northern Germany

Ich habe 3 oder 4 PETG-Filamente ausprobiert. Auch das von Overture. Ich meinte aber, das das Bambulab PETG Translucent das beste Ergebnis geliefert hat. Dann bin ich einem Artikel gefolgt "How to Print HD Glass". Mit einer extrem niedrigen Druckgeschwindigkeit, gleichmäßig ausgerichtetes Infill und einer mininmale Layerhöhe lassen sich nach dieser Anleitung nahezu durchsichtige Blöcke drucken. Allerdings lässt sich das sich nicht so ohne weiteres auf die Struktur des Zylinders übertragen. Außerdem sollte die Druckzeit ca. 4 Tage mit diesen Einstellungen betragen.

Die besten Ergebnisse habe ich dann am Ende mit einer 0,8mm Nozzle und einer Layerhöhe von 0,4 erreicht. Die Wände sind knapp 2 mm dick, also immer 2 Linien.

[lennypumper]

A two-part project like the Monster Tube would be much easier to design and print.

I have a little something for you: https://www.printables.com/model/796164 ... sball-pump

absolutly. I defnitly will take a look at your design. Can you share a pciture of the final result ?

[nohapony]

A two-part project like the Monster Tube would be much easier to design and print.

I have a little something for you: https://www.printables.com/model/796164 ... sball-pump

absolutly. I defnitly will take a look at your design. Can you share a pciture of the final result ?

see here viewtopic.php?p=385594#p385594

[TinyMe]

Hi Guys,
this is my selfdesigned and printed Tube. It was inspired by my bullmaster jr.
It‘s not as clean as the original, but i have a pretty good Look on the things going on in there…
Many Greets vom Germany…

It must be awful having a dick big enough to fill that tube…

[cyborg]

Is there a software that makes it easy to design things?

I installed Blender and freecat but I can't seem to get to grips with them.

I don't even know how to use finished files can edit (change size, etc.).

A simple software where you drag a corner of the model with the mouse to change the model.... So simple

I just started with 3d printing and cad design about 2 months ago. I use fusion 360 to design and export the files for 3d printing. For design sometimes you have to think about your shapes differently. Like to make a seal similar to the stj seal it's basically a tall rectangle with a fillet on 2 edges. There are a lot of videos on YouTube on how to use fusion.

[lennypumper]

Hi Guys,
this is my selfdesigned and printed Tube. It was inspired by my bullmaster jr.
It‘s not as clean as the original, but i have a pretty good Look on the things going on in there…
Many Greets vom Germany…

It must be awful having a dick big enough to fill that tube…

seems to me there is a kind of magnifying effect from the tube...

[lennypumper]

Hi Guys,

here my latest design with integrated seal.

The dimension is similar to the Bullmaster. Whilst a bit shorter the sections for the balls is a little bit bigger..

You can download the stl at §D Cults:
https://cults3d.com/en/3d-model/naughti ... -ball-pump

Have fun !

[Polarbear65]

It’s awesome, it’s like work of art!

[Pumping Now]

Sketchup is free & has .stl file export to free Cura 3d printer slicer... All fairly simple.
Onshape online has a lot more options...