Bullmaster like tube

[shyguy_8121]

Trying to grow with my home made tube. It takes a long time to get huge. I find a bigger jar is better but maybe I would have to pack this first.

[Pumping Now]

Bullmaster packed just looks sexier.

[shyguy_8121]

Starting with warm water. I like the shape to be round like a perfect sphere.

[Jreckuall]

Is this a home made tube

[shyguy_8121]

Yes, built to be close to the bullmaster magnum.

[shyguy_8121]

An hour and a half in the tube. Feels good.

[shyguy_8121]

I had my best pump day largest size in August with this tube and grew pretty big but today I pumped about 3 hours and didn't get nearly as big. I was using warm water and taking breaks every 20 to 30 minutes. Is low pressure (2 to 3") better than 5"? Maybe hydration is what is needed? I try to drink a lot of water. I still don't know how you guys get to be 15" around. By the next day most of my gains are gone and it feels like starting all over. Any tips to grow big?

[Japsterpum]

I think your Bullmaster is great, can you describe how you did it? Drink a lot when pumping, keep warm and don't use too much pressure, 3-4mmhg is enough. It takes a bit of time. Session 30-45 minutes, then a break and massage. Many people use olive oil or coconut butter to rub in afterwards so that the skin stays supple. These are the tips I've picked up from experienced pumpers and they work well. You'll grow over time. Many people have been pumping for years to get great results.

[shyguy_8121]

Use plastic eggs cut in to shape of a 4" round tube. Lots of sanding with different grits. Eventually it will conform to the shape of the tube. Super glue them on. Takes some time. Drill small holes and file the openings after you trace the eggs around the tube. It's pretty close to one though I have never had. If I had to do again I would make the top pocket longer but plenty of room to grow.

[Japsterpum]

Thanks for the info, sounds interesting but also like a lot of work.

[shyguy_8121]

a 4 x 5" egg. The egg follows the 4" circumference of the tube. If you hold up the egg on it's end parallel to the end of the tube, you can sight the shape that it would take. Once you know the shape, you can cut much faster. Use high grit to start, 80-120, then to 220 and 320. Using the 4" tube as the shaper for the inside of the egg when it is cut to shape (rough). Trace out the egg..but I chose to leave 1/4" border making the hole cut in the tube smaller than the egg. The edges have been filed and sanded smooth. The top egg was a different story, that required a much smoother transition. No sharp edges at all. To really make one on a professional level, I would take a block of acrylic, and dremel down to the teardrop shape, then sand and polish. Polishing it to get clear would be difficult, but it could be done.

[Japsterpum]

Well done

[AndyJ]

Very nice workmanship there.

[Pumping Now]

IMO getting out of a packed BullMaster (Esp. Magnum) can be a chore.
When I make another tube, it'll only have the cock pocket on top.
Go for ball length & cock girth & easier to withdraw.
4 1/2 x 12" -
yeah, it'll pull in some unwanted pubis pad....

[shyguy_8121]

To be that packed that a Bullmaster (Standard or Magnum) is too small, wow. I have been thinking about the bottom side of the balls flush against the straight 5" diameter tube I made..and wondered if there is any advantage to a Monster Tube? It looks like the balls would be floating, not hitting any sides of the tube and thus would expand more easily? I notice they turn dark as if less oxygenated blood is circulating. Is that normal?