HOME MADE 6 INCH x 10 INCH TUBE

[Huge4Me]

I am taking delivery of a replacementy Sun Tea Jar today. The inside opening on my Pump Toys seal is much too small for when I pump up fully. I'll be fabricating a seal following your advice. So thanks for sharing the techical stuff. And thanks for posting photos of that wonderfully enormous pumped package. KEEP GETTING HUGE. THEN GET EVEN BIGGER THAN THAT. AND ENJOY EVERY INCH AND EVERY MOMENT OF YOUR PUMPING EXPERIENCE

[pumpman12]

Hey HUGE4ME have you seen my thread on making the seal ?? Its very helpful when shaping the silicone

[pumpman12]

So I'm away and PUMPING !!!
Getting two times a day in my 6 X 10 and getting some great results. Here are a group of pics, let me know what you think >Oh wait these first pics are my 5 X 12

[WatchMeGrow]

Hell yeah ! Grow grow grow !

[tout69]

That looks epic, great work!

[pumpman12]

As always ... THANK YOU to all the great comments. Here are the next set of pics

[Ballooon111]

In my thread on 5 inch X 10 inch tube you will see how easy it is to exit the tube. As I came across this glass vase at a local store thought wow this would make a really nice pump tube. Here are some pics of the new tube. I have a bunch of " HOW TO " pics on the making of this tube. Let me know if you want to see how I did it. The first pic is the 5 inch side by side with the 6 inch.

Great job, it looks like it's performing well.

[pumpman12]

More pics.....slowly getting bigger

[pumpman12]

NOW......if you get stuck in your tube after pumping, if it's a Bullmaster a Two stage or a one gallon jar you need to watch this vid. The key is the homemade seal is part of the tube. It flexes' when you are trying to exit. You will see it takes about 30 seconds to get out

[pumpman12]

Next vid .... putting on my ball strap

[Fr0st]

Where’d you get that strap. Looks effective and comfortable

[Dink]

Looks great.

Where is you get the tube? I've been looking for something bigger than my 5".

Also, I've found collapsible silicone bowls to be just at, or slightly bigger than 6". Cut a hole in the bottom and you have a nice, cheap, easy to make seal.

[pumpman12]

Yes , the ball strap is home made as well. It's all about comfort.

[getbigstj]

Guys the easiest stuff I’ve found to work with is let’s resin which you can buy from Amazon. Find a container that’s just bigger than your opening and and a 3” glass for the center opening. Suspend your tube down into the silicone at proper depth! Let it cure for 24 hours and your done!!

I can attest to this post that this stuff is legit. I made a seal out of this yesterday early AM 6:30 came home around 5:30 it was fully cured I even hopped in it and no problems what so ever so it cures in 6 hours like it says and I made a HUGE deal out of it the jar it goes around has an 6 -5 inch opening I made the center diameter of the seal 3.5 inch opening so it’s the same width as monster tube opening maybe a full 3.7 and the total circumference of the tube I put it on is 28 around the glass inside could be 26 total maybe 27 anyways larger than the 22 the monster carries and let me tell you this thing got big big fast this morning I was even able to put my penis pump gun in the opening and it stayed there no fluctuations in HG put a lil epsom salts in the jar with warm water and heating pad a got up to 12.5 inches around in 1hr 20 min I used this tube a few weekends ago it took me 4.5 in tube time 6 total to get the 16.2 inches around so I’m looking forward to how big I can get in this thing now that I have this seal. Looking at some SCARY big pumps in the near future “tis the season” I’ll post some pictures of it when I get home pumpman12 and everyone else should give this product a try. I see why you guys who have had monstertubes get as big as quick as you do! Tube is massive! And again I have a glass version of a monster tube with BIGGER dimensions I’m kinda excited and scared of how big I could actually get with this new setup.

[getbigstj]

Here are some pictures 2.5 x 12 inch for comparison