Ball stretching

Talk about ball pumping, stretching, ball enlargement techniques.

Moderator: bigray57

baccrkr
Posts: 58
Joined: Wed Jul 24, 2002 7:43 pm
Location: So Calif

Post by baccrkr »

BBBTWO

Thanks for the compliant. Your right it always fun to see how far I can stretch at any given time. I hope to be adding more soon.

I love the feel of wearing more and more collars, because of feeling of the weight and feeling them swinging as I walk all day. Also, love the feeling of using heavier weights on the parachute.

BBBTWO in one of your pictures you were using a stretching device you made like one that Franky uses, out of fuel line and cable, could you give me details about how you made it?
MWM 52 6'3"
Just can't get enough of stretching and pumping.
BBBTWO
Posts: 275
Joined: Tue Dec 21, 2004 4:40 am

Post by BBBTWO »

Baccrkr. I tried two times to give you the infor you needed for the stretcher. Both times it didn't post. I'll try tomarrow. BBBTWO
baccrkr
Posts: 58
Joined: Wed Jul 24, 2002 7:43 pm
Location: So Calif

Post by baccrkr »

BBBTwo
Thanks for trying. I hope it comes through.

It looks fairly simple, but I would like to know the details.

Thanks again

baccrkr
MWM 52 6'3"
Just can't get enough of stretching and pumping.
jojouk
Posts: 3
Joined: Sat Sep 03, 2005 11:11 pm
Location: london uk

Post by jojouk »

i was inspired to try weights by your pics congrats
Attachments
wrapped half inch lead pipe in duct tape weighing 1 lbs 3 1/2 ozs or 552 grms
wrapped half inch lead pipe in duct tape weighing 1 lbs 3 1/2 ozs or 552 grms
Picture 004.jpg (57 KiB) Viewed 3058 times
illbill
Posts: 5
Joined: Fri Aug 26, 2005 9:42 am

Post by illbill »

I tryed this one night and it hurt, alot. How much pain do you experience?
Made my balls hang quite low in a short session though.
BBBTWO
Posts: 275
Joined: Tue Dec 21, 2004 4:40 am

Post by BBBTWO »

Baccrkr. the fuel hose stretcher is made from the following. Hose, 16in long, inside dia 3/16, outside dia 1/2in. Cable 30in long, 1/8in dia. A 3/4in pvc "T" fitting. The silver items on the cable are ferrules. To make. Cut hose and cable to lenght. Run cable thru hose. Loop cable thru ferrules. With dull chisel, place in ferrule groove and strike chisel with hammer. Do this on both sides of each ferrule. Make sure ferrules are tight on the cable. Install "T" fitting. You should beable to purchase all the items at a hardware store. If they do not have a thick walled hose, try a auto parts store. Below are a few pics to help you out. Hope to see you soon using your new stretcher. BBBTWO
BBBTWO
Posts: 275
Joined: Tue Dec 21, 2004 4:40 am

Post by BBBTWO »

open
Attachments
open04jpg.jpg
open04jpg.jpg (74.96 KiB) Viewed 2932 times
BBBTWO
Posts: 275
Joined: Tue Dec 21, 2004 4:40 am

Post by BBBTWO »

closed
Attachments
closed03.jpg
closed03.jpg (60.33 KiB) Viewed 2931 times
BBBTWO
Posts: 275
Joined: Tue Dec 21, 2004 4:40 am

Post by BBBTWO »

apart
Attachments
apart04.jpg
apart04.jpg (61 KiB) Viewed 2933 times
BBBTWO
Posts: 275
Joined: Tue Dec 21, 2004 4:40 am

Post by BBBTWO »

ferrules
jojouk
Posts: 3
Joined: Sat Sep 03, 2005 11:11 pm
Location: london uk

Post by jojouk »

two weights on my balls weighinga total of 2 lbs 9and 3/4 ozs or1182 grms . sack has not streched enough too go for 3 weights yet.
Attachments
Picture 005.jpg
Picture 005.jpg (56.3 KiB) Viewed 2828 times
baccrkr
Posts: 58
Joined: Wed Jul 24, 2002 7:43 pm
Location: So Calif

Post by baccrkr »

BBBTWO

Thanks for the details and photos. It's off to Lowes for me.... :D

jojouk
looking good. keep stretching.
MWM 52 6'3"
Just can't get enough of stretching and pumping.
Post Reply