TinyMe! From tiny to...

[SFBallpumper]

The photo shows the black washers on the fittings. These should be replaced if you’re having a hard time keeping a seal.

[TinyMe]

The photo shows the black washers on the fittings. These should be replaced if you’re having a hard time keeping a seal.

Thanks man. I’ll look at adding more lube too!

[PeterPrinciple]

Any thoughts on how to program the pulsating electric pump (boob pump?) to get massive Tanuki type balls?

Thanks

PP

[TinyMe]

Any thoughts on how to program the pulsating electric pump (boob pump?) to get massive Tanuki type balls?

Thanks

PP

No idea whatsoever I’m afraid. I’m in finance, not engineering!

[TinyMe]

Had a little pump today (2 x 90 mins or thereabouts).

Apparently tomorrow, I’ll be trying it with socks on! And today I’m going to drink way more than I normally would and see if these two things make a difference.

Anyway, for today, this is it...

[TinyMe]

As per my intention...

My feet are toastie warm and Ive drunk about a litre of water so far...

[HrnMntMan]

You are for sure warm and cozy. Hope it goes well

[SFBallpumper]

Looks great!!!

[TinyMe]

Warm feet was the only real result of my actions yesterday.

And pissing a lot...

I’ll persevere...

[SFBallpumper]

Before you get out of bed and before you throw back the covers, check your balls. Are they relaxed? If so, pump under the covers. Your body needs to be warm for your balls to hang.

[SFBallpumper]

The other thing you might try is wet pumping (pumping with warm water in the tube). Unless you're using a pump that can tolerate getting water inside it, you need to have a water trap. Just make sure that the water trap is below the level of your pump so that water doesn't flow into it. Getting water inside several kinds of pumps will ruin them. Been there, done that.

[SFBallpumper]

Here's the water trap I use on Amazon. You don't need any kind of hose clamps or adapters as long as you're using the standard ¼ inside diameter vinyl hosing that comes with almost every pump.

https://www.amazon.com/Mityvac-MVA6005- ... 205&sr=8-3

[TinyMe]

Some great advice there SFB, thank you

My balls are usually warm when I wake up, but once I get up to pee (straight away) that’s usually the end of that! Then I have to go through the rigmarole of setting everything up to use, and by that time, they can be in any sort of state!

I’ve got a trap that came with the brake bleeder kit I bought last year. I used it for a little while with my glass jar, but as the water cooled down quite quickly, I got fed up of getting back out and in again so I gave up.

However, I suppose now I have my heat blanket, that would help keep the water warm, but I suppose the real concern is keeping water and electricity apart - there’s always an element of risk and I’d hate for my g/f to come home one day and find me dead with fried balls!!

Having said that, I’m home alone tomorrow, so might give it a go

[bentslong]

Hey to stop water or condensation in tube I use paper towel.
I twist up a strip of paper towel and put it the tube at both ends.
A piece at pump end and a piece jar end it soaks up any condensation.
If you use a water trap i would stuff it with paper towel to help trap any water.
I got the idea from my air line filter for my plasma cuter/
It has a canister with a roll of paper in it like a toilet roll.. it filters out any dirt water and oil in the line.
It will help hold the water to if you knock over your water trap to.

[TinyMe]

Hey to stop water or condensation in tube I use paper towel.
I twist up a strip of paper towel and put it the tube at both ends.
A piece at pump end and a piece jar end it soaks up any condensation.
If you use a water trap i would stuff it with paper towel to help trap any water.
I got the idea from my air line filter for my plasma cuter/
It has a canister with a roll of paper in it like a toilet roll.. it filters out any dirt water and oil in the line.
It will help hold the water to if you knock over your water trap to.

Thanks for the advice!