Bullmaster tube.
Moderator: bigray57
-
- Posts: 1319
- Joined: Fri Aug 08, 2008 8:08 pm
- Location: Ontario, Canada
Bullmaster tube.
Want to see if anyone has a Magnum or regular Bullmaster tube for sale. I have trouble getting out of my 357 after about a half hour. Just throwing it out here. Please message
-
- Posts: 30
- Joined: Sun Aug 28, 2022 9:06 am
Re: Bullmaster tube.
It’s rough out there. I’ve been trying to get a magnum from pumptoys for years, every time I email them I get the same response about supply chain and material issues that I’ve gotten since 2020. It’s been nearly 4 years since all that nonsense and somehow pumptoys still can’t figure it out. Super disappointing. I’ve bought half a dozen cylinders since then from Monster and LA pump without issues. Monster tube senior is by far my favorite right now.
-
- Posts: 1319
- Joined: Fri Aug 08, 2008 8:08 pm
- Location: Ontario, Canada
Re: Bullmaster tube.
I know. Pretty disappointing. I have both monster tubes but I like the comfort of the 357. Just fill it too fast and hard to exit. Why I'm looking for a Magnum. Hopefully sometime soonMaskedHero wrote: ↑Tue Nov 21, 2023 4:52 am It’s rough out there. I’ve been trying to get a magnum from pumptoys for years, every time I email them I get the same response about supply chain and material issues that I’ve gotten since 2020. It’s been nearly 4 years since all that nonsense and somehow pumptoys still can’t figure it out. Super disappointing. I’ve bought half a dozen cylinders since then from Monster and LA pump without issues. Monster tube senior is by far my favorite right now.
-
- Posts: 89
- Joined: Fri Oct 02, 2009 1:01 am
- Location: Austria, Stockerau
Re: Bullmaster tube.
I am looking for a Bullmaster Magnum too with no avail. The whole shortage thing is just bullshit, as supply chains are filled to the brim due to the recent recession.
I have given up all hope for getting a Bullmaster Magnum anytime in the next years. Probably gonna experiment myself on creating a replica with the same bulges for the balls…
I have given up all hope for getting a Bullmaster Magnum anytime in the next years. Probably gonna experiment myself on creating a replica with the same bulges for the balls…
I LOOOVE PUMPING, but I just cant get that seal over to Europe, without paying for shipping as much as for the seal itself . So I am limited with time of my pumping session (And so are results)
http://www.xtube.com/community/profile. ... r=GinLover
http://www.xtube.com/community/profile. ... r=GinLover
- BlkPumper
- Posts: 690
- Joined: Sat Apr 05, 2014 8:01 am
- Location: DMV
- Contact:
Re: Bullmaster tube.
It's a shame so disappointed too. we be trying to get hold of the product to no avail for years now. wish someone else made the same product
-
- Posts: 1319
- Joined: Fri Aug 08, 2008 8:08 pm
- Location: Ontario, Canada
Re: Bullmaster tube.
If there was a new manufacturer I would be their first customer
-
- Posts: 32
- Joined: Thu Apr 07, 2005 5:48 am
- Location: Germany
Re: Bullmaster tube.
They, Pumptoys.com, have enough demand for the Magnum, Corona is no longer a major factor and suppliers should have their stock replenished. So I think Dave is going to sell everything or as much as possible, shut down shop, and pumptoys will be a thing of the past.
I wish they would tell the truth instead of jerking everyone off!!
I wish they would tell the truth instead of jerking everyone off!!
- Pumping Now
- Posts: 1174
- Joined: Thu Jul 21, 2016 5:25 am
Re: Bullmaster tube.
Bull Master Magnum - if anyone makes a replica, here's changes to original I'd like.
1. Make ball pockets bigger & longer.
2. Make penis pocket taller.
3. Mold on a flared mouth.
4. Add another threaded hole at the end bottom of the tube. Good place to release cooled water, etc.
Of course, the bigger the inside volume is, it'll be even harder to get out.
5. Make it splittable, like Monster tube?
I prefer magnum's straight entry compared to cone shaped monster entry.
1. Make ball pockets bigger & longer.
2. Make penis pocket taller.
3. Mold on a flared mouth.
4. Add another threaded hole at the end bottom of the tube. Good place to release cooled water, etc.
Of course, the bigger the inside volume is, it'll be even harder to get out.
5. Make it splittable, like Monster tube?
I prefer magnum's straight entry compared to cone shaped monster entry.
Balls flopping free like a bull. To my knees, and beyond!
-
- Posts: 1319
- Joined: Fri Aug 08, 2008 8:08 pm
- Location: Ontario, Canada
Re: Bullmaster tube.
You make the Bull Monster and I'll be your first CustomerPumping Now wrote: ↑Fri Dec 08, 2023 5:45 am Bull Master Magnum - if anyone makes a replica, here's changes to original I'd like.
1. Make ball pockets bigger & longer.
2. Make penis pocket taller.
3. Mold on a flared mouth.
4. Add another threaded hole at the end bottom of the tube. Good place to release cooled water, etc.
Of course, the bigger the inside volume is, it'll be even harder to get out.
5. Make it splittable, like Monster tube?
I prefer magnum's straight entry compared to cone shaped monster entry.