I am looking for a 1.25 tube, approx. 9 inches or longer.
I quit pumping for 5 years and my cock has shrunk...
A 1.50 tube is quite big & I keep loosing sucktion.
Yes I am the true meaning of a "pencil dick" that is 7 inches long.
Looking for 1.25 tube
Moderator: bigray57
-
- Posts: 65
- Joined: Thu Aug 01, 2013 8:26 pm
- Location: Lawrenceville/ATL Georgia
-
- Posts: 131
- Joined: Thu Sep 04, 2014 6:34 am
Re: Looking for 1.25 tube
I used to make my own. Be careful, those narrow tubes put too much pressure on the glans and that can only mean blisters. I'm sure you know what your doing though! Safe pumping!
-
- Posts: 65
- Joined: Thu Aug 01, 2013 8:26 pm
- Location: Lawrenceville/ATL Georgia
Re: Looking for 1.25 tube
I tried making my own.....don't work that good.
Being small in size /stature, my cock is 7 inches long when hard--but only as round as my thumb.
A 1.50 tube sucks my balls in and hurts like hell.
Being small in size /stature, my cock is 7 inches long when hard--but only as round as my thumb.
A 1.50 tube sucks my balls in and hurts like hell.
-
- Posts: 69
- Joined: Wed Jun 01, 2011 1:18 pm
- Location: Vancouver Canada
Re: Looking for 1.25 tube
I started with one of those plastic pistol pumps with the 'patented' senso sleeve (silicone?). The sleeve kind of restrains your penis as you move toward packing. It's almost a type of packing in itself. These plastic pumps can be inexpensive on the internet. I still swear by the idea of a sleeve inside the tube. While the pistol pump cylinder is two inches plus, the sleeve acts to help force some width even if the tube sides are still out of reach.
I have used that sleeve in a proper tube with similar results.
Just a thought.
I have used that sleeve in a proper tube with similar results.
Just a thought.
-
- Posts: 139
- Joined: Mon Dec 27, 2004 2:07 am
Re: Looking for 1.25 tube
I have seen that Vacu-Tech offer a 1.25 tube, and in 5-12 inches length.
- baker08
- Posts: 92
- Joined: Sun Jul 15, 2012 8:04 am
Re: Looking for 1.25 tube
Back in my early days i made my own tube.
I used an empty tube of clear bathroom silicone.
It was my favourite starter tube till i could step-up.
I used an empty tube of clear bathroom silicone.
It was my favourite starter tube till i could step-up.
-
- Posts: 434
- Joined: Wed Dec 28, 2011 10:30 am
- Location: Philadelphia, PA
- Contact:
Re: Looking for 1.25 tube
LeLuv on Ebay has a 1.35 x 9; that might work.
beginning at 4.5 girth, working toward having an unpumped girth of 6-6.5
-
- Posts: 11
- Joined: Thu Aug 28, 2003 7:21 am
- Location: San DiegO, CA
Re: Looking for 1.25 tube
Hello Bosco Bear,
Me again. I am almost sure you can find that size on eBay. The retailer's name is LeLuv. I just so happen to have some coupon codes for you if you like and only because I just purchased something recently.
5% off any purchase: use code SAVE5
10% off $50: use promo code SAVE10
20% off $100: use promo code SAVE20
Hope this helps.
Tony
Me again. I am almost sure you can find that size on eBay. The retailer's name is LeLuv. I just so happen to have some coupon codes for you if you like and only because I just purchased something recently.
5% off any purchase: use code SAVE5
10% off $50: use promo code SAVE10
20% off $100: use promo code SAVE20
Hope this helps.
Tony
-
- Posts: 4
- Joined: Fri Jan 11, 2013 9:18 pm
Re: Looking for 1.25 tube
i have a 1.25" cylinder that i'm trying to fill so fellow pencil dick here. hahaha way shorter than 7" though.
-
- Posts: 407
- Joined: Mon Dec 27, 2004 1:35 am
Re: Looking for 1.25 tube
Loosing suction is not the size of the tube but could be that you need to shave closer or use another lube. You could have a leak in the pump also.
-
- Posts: 1115
- Joined: Fri Jun 19, 2015 10:32 am
- Location: Sydney Australia
Re: Looking for 1.25 tube
I wanted a tight tube but couldn't find a small tube. I went to the hardware store and bought clear tubing used in fish tanks. I cut the tube to fit the length of my 50mm tube, placing a nick in the top of the tube it to let air in and out. I then mounted this inner tube over the tube sleeve and shoved the sleave into the 50 mm tube. I noted that the tube is not really round but more like the shape of my penis, flatter on the bottom and rounder over the top, works great!bosco bear wrote:I tried making my own.....don't work that good.
Being small in size /stature, my cock is 7 inches long when hard--but only as round as my thumb.
A 1.50 tube sucks my balls in and hurts like hell.