forums.newart.com

[ballpumper808]

i just got my monstertube sr. and would like your info, inspiration and pics of how you got your 18+" balls. how long did stay in your tube? what was your pressure? breaks schedule? etc.? how do you get water in the "clamshell" and not spill at water changes (my problem)? my personal best is only 15".

thank you fellow big ball pumpers for any info, inspiration, and pics.

[johnnysilicone]

I love it monster sized!!!

[ballpumper808]

nice big balls but how much is pump with MT and how much is silicone? thanks

[POOLBOY66]

I use the MT, and I usually fill the MT with warm/hot water before I start. I pump for 45 min. then stop and rest for 10 min. Then refill the tube with fresh warm/hot water and pmp for another 45 min.. This usually ets me to 17". If I decide to go longer I release the pressure and leave the MT on. Then I pump for another45 min., this gets me to 18", however that is as big as I seem to get. I sometimes wrap the tube in a heating pad to keep everything warm.

[DELETED]

DELETED

[ballpumper808]

thanks poolboy and surfgar for comments and info.

[mRuss]

15" is not bad
I don't always get good pump results, some days are better than others. On the days when I hit my personal bests of 15.5 and then 16.75 I pumped for at least 3 or 4 hours. Use an electric pump if you can, I always do. And don't put the pressure too high, i use 4"Hg now and it works just fine.

lastly be sure you're measuring properly, too.. around the balls ONLY, no cock involved in the measurement

[vckay]

very nice, thx 4 sharing

[cirus]

I have just posted this question plus some photos on the "2 stage question" thread, then noticed that this thread might be more apropriate.


I am at the stage of considering something bigger. I have a two stage with a 3.5" entry and keep geting seriusly stuck in it. I almost fill the 2nd stage to the end. Reversing the pressure to blow things out is very painfull even when pulling out my cock first and then blowing my balls out one at a time. each ball has a hard time getting out of the 3.5" opening.
To help the situation I have tried transfering to a straight 3.5" x 10" cylinder before things have got to tight in the two stage. But i fill that tube to the end so it has become obvius that I need something bigger.
I have considered a monstertube but hear stories about pinching when putting back on during a pump session. Also I tend to pump with warm water which could be dificult to change if you have to open to get out and back in again. Your comments would be apreciated.
My other thought is to go for a 12" longjohny from pumptoys, I belive that has a 4" entry and would be a straight cylinder.
I should say that I pump for length (I also have a 2.75" x 12 cylinder but that squeezes my balls up a bit and I am getting to within 1" of the end of that) so the longjohny may be the answere now that they do longer lengths.
Any other thoughts would be welcome.
cirus.

[DELETED]

DELETED

[xstr8guy]

[DickBulger]

[cirus]

Thanks for all the input guys, lots to think about. Just had a thought about DB's sugestion for getting the water in, how about an aditional connector in the monstertube to drop a line into a bowl of warm water and then pump on the other connector to draw the water in. Maybe Monstertube would supply one with two connectors. It would seem best to leave the monstertube on during rest periods and then refill with water with it still on, to avoid any chance of pinching. Skin gets quite fragile after being stretched. I like the idea of keeping the entry down as small as posible to avoid the dreaded belly bulge, the 3 1/2" entry on the monstertube seems about right. Does any of this make sense?
Thanks again, cirus.

[DickBulger]

[vango]

Just bought the "large" MT, used it twice, but should have gone for the smaller opening MT, no trouble "getting out"...but pump is more skin than C/B's. Any suggestions, offers, trades??