forums.newart.com

ScorpioRising · Joined: 11 Jan 2004 Posts: 1507 Location: x0|So Cal|USA||||

I agree--stainless your photos and your handmade penis plug are works of art (deliciously hot works of art I might add). My photos are no comparison and my penis plug is just an ordinary one that I bought but there is no way its going to fall out (not unless I stretch my hole to a much larger size). Here are some photos of me playing with it the other night.
Scorpio

rogj55 · Joined: 29 Aug 2007 Posts: 52 Location: Nashville, TN

Scorpio.,Nice pics & cum shot! Would like to see some more.

seahorses · Posted: Sun Mar 30, 2008 9:30 pm Post subject:

I’ve been following this thread for a while now; initially because my pee hole was reducing due to the amount of pumping I do and I wanted to restore it. However, I’m too tight to pay £40, or what ever for a custom made job so I’ve made a few of my own. The trick is to get a bulge in the device that stops it from being ejected; it also requires a flange on the end to stop it from slipping all the way in; I should hate to end up red faced in the casualty department!

Here’s a couple of pic’s of my latest endeavour; it’s relatively cheap to make and dead easy. I got hold of some tubing similar to the type use to connect your cylinder to your pump, from my local D.I.Y store. I brought a variety of sizes for a progression.

To make one, I took about a 10” length, of tubing folded it in half and put the folded end in a saucepan of boiling water for a few minutes to make it hot, soft and very pliable. Then quickly straightening the tube I pulled the ends apart, the hot, soft pliable middle stretching and becoming thin. Holding it in that position I ran it under the cold tap to set it. Cutting it in half I then had two tubes that tapered one end. Next I inserted a golf “Tee” in the fat end of the tube I continued working on, compressing the tube down against the flange of the “Tee” and holding it firmly in place with a pair of pliers. Holding it back in the boiling water for a few minutes the tube started to take on the shape of the flange, then it was back under the cold water to set. To form the bulge in the tube in the picture, I used a piece of plastic tube slightly bigger than the I/D of the nylon tube and forced to the required position. It took about 10 minutes to produce the complete thing. A few turns of the tapered end in a pencil sharpener not only gives a steep taper on the very end, aiding insertion, but by making it even thinner it also makes it softer and less inclined to irritate.

I also used plastic beads for fishing to make the bulge in some tubes and because everything is hollow there’s no need to remove the plug to pee. Being nylon tubing you can make it any length you wish and you can play around with various designs; altering the position of the bulge etc.

seahorses · Posted: Sun Mar 30, 2008 9:31 pm Post subject:

With it in

dragonroger · Joined: 21 Mar 2008 Posts: 1

Yes you can fuck with them in. I have a 8.5mm apadravia and a few different size wonds custom made to fit with the apadravia + a few differnt size balls largest being 2". Hard to get biggest balls in but no compains when in. have fun & enjoy stretching to you wond size. Smile

nas_ana · Joined: 31 Jan 2008 Posts: 2

After lurking on this board for a while I got myself a penis plug too. I like this toy Razz

It took a few attempts before I could get it in, and when I succeeded the feeling was amazing. I don't know about fucking with it though. In any case I would recommend to pull your dick out before cumming, because I tried cumming with the plug inserted and at first nothing came out (not a single drop, very cool), but then all of a sudden the plug rocketed out of my dick followed by a big cum load. I've heard people get injured from flying champaign corks, and I would like to see the doctor's face when you tell him you got hurt by a flying penis plug Laughing

I made some pictures as well. Here you go.

jonnie · Joined: 20 Jun 2003 Posts: 13 Location: x0||||||

Whoops. Made a mistake & posted as "new" rather than a reply. Anyway,
let's get this topic back up to page one. This was one of the best series so do we have any more pictures or comments to add?

Made a huge milestone today as I finally got my 13mm (just over half an inch) sound to go in all the way. Great feeling, especially after having difficulty breaking that barrier. Next step is to see if I can get the 14mm sound to enter. Will post more pictures when I'm successful with getting the full 8 inches of the sound all the way in.

steelboy · Joined: 10 Jan 2006 Posts: 108 Location: germany

hey,
here is my short plug Very Happy

max. diameter is 12mm !

steelboy

darth · Joined: 16 Jun 2002 Posts: 26

the plug with the hole thru it is real hot. who has the best prices for them?

darth · Joined: 16 Jun 2002 Posts: 26

I just ordered my "little fucker penis plug, are you guys still using yours and have you had any problems?

Plum_Crazy · Joined: 27 Oct 2006 Posts: 8 Location: Melbourne, AUS

You can also try www.penisplugsablaze.com. The guy there builds also sort of plugs and wands to order. I have had a couple of custom pee-thru plugs made and they have been of the best quality, highly recommended. Shipped form the US to AU in the space of 10-14 days from order, build to delivery.

f40 · Joined: 10 Aug 2008 Posts: 7

Hello guys.....I'm a new comer........interesting things..........

steelboy · Joined: 10 Jan 2006 Posts: 108 Location: germany

hi,
pics from my penis and urethral stretching toy.

steelboy

MoLonghorn · Joined: 01 Aug 2006 Posts: 33

Hi guys, have been wearing my plug for longer periods of time not that I can get it in. What kind of lube are you using that doesn't dry out so that the plug sticks to the uretha when going to remove it?

tomk · Joined: 03 Apr 2003 Posts: 616

Use a triple-anitbiotic like a neosporin.